A high-quality, flat acrylic latex paint with excellent hiding properties. This interior/exterior, self-priming, mildew resistant finish also provides excellent adhesion and water repellency on properly prepared interior or exterior smooth, rough and textured masonry, stucco and brick surfaces. This water-based formula is designed to accentuate all textured surfaces while achieving a natural look. It is alkali-resistant, easy to apply, lasts 20 years in all climatic conditions and cleans up with soap and water.
- White 270 - MSDS
- Pastel Base 271 - MSDS
Where To Use
Great for new or old, previously coated interior or exterior vertical brick, masonry, stucco, concrete, cement, slate, stone, cinder block, adobe and clay. Allow new stucco and masonry to cure for 30 days before painting. Also suitable for wood applications such as eaves, overhangs and trim where necessary.
May be used on galvanized gutters or flashing areas.
Not recommended for any horizontal surfaces subject to foot traffic, including concrete and masonry floors. Use BEHR PREMIUM PLUS® PORCH & FLOOR PAINT, BEHR NO. 800 SOLID COLOR CONCRETE STAIN, BEHR NO. 850 SEMI-TRANSPARENT CONCRETE STAIN or BEHR NO. 900 1-PART EPOXY ACRYLIC CONCRETE & GARAGE FLOOR PAINT for these surfaces (see labels for application limitations).
(The following steps are recommended for best results)
If surface has been previously treated with a waterproofing sealer or coating, check manufacturer's specifications before painting these surfaces.
Remove all loose, peeling paint or stain.
All surfaces must be free of dirt, chalk, mildew, oily substances, crumbling masonry, wax and any signs of gloss.
To remove dirt and grease use BEHR® NO. 990 CONCRETE CLEANER & DEGREASER. Remove mildew stains with BEHR® NO. 62 MULTI-SURFACE CLEANER & MILDEW STAIN REMOVER. Refer to product labels for specific instructions.
On galvanized metal, use a diluted solution of BEHR NO. 991 CONCRETE ETCHER & RUST REMOVER to prepare surface. Refer to product label for specific instructions.
Powerwash to remove all chalk, rinse and allow a minimum of 24 hours to dry.
Test surface for additional signs of chalk by wiping hand across surface.
If there is a white powdery substance left on your hand, pressure wash again to remove all signs of chalk. Rinse and allow to dry.
If any chalk remains on the surface, prime with PREMIUM PLUS® EXTERIOR WATER-BASED PRIMER & SEALER NO. 436 prior to application of BEHR NO. 270/271 FLAT MASONRY, STUCCO & BRICK PAINT. Refer to product label for specific instructions. Primer is not necessary if chalk has been completely removed.
Scuff sand all glossy surfaces.
Cracks and gaps wider than 1/16" (1.5 mm) should be routed open, dusted and patched with a quality patching compound. Sand smooth. Use an acrylic caulk around windows, doors and trim. Scuff sand glossy surfaces.
Spot prime all patched areas with PREMIUM PLUS® EXTERIOR WATER-BASED PRIMER & SEALER NO. 436 tinted to the color of the topcoat. Refer to product label for specific instructions.
If previously sealed or coated, check manufacturer's specifications before painting.
Product has been formulated for use at package consistency, therefore, thinning is not recommended.
When working with more than one container of the same color, intermix all cans of same product to ensure color uniformity.
Stir paint before and occasionally during application.
For best results, use product when surface and air temperatures are between 50-90°F (10-32°C). Do not apply if temperature is below 50ºF or if rain or heavy dew is expected within 24 hours.
Avoid applying in direct sunlight to a hot surface. If temperature exceeds 90ºF, hose down surface and allow to dry to a damp condition before painting.
For rough textured surfaces, apply at a spread rate of about 250-300 sq. ft. (23-28m²) per gallon using a 3/4"-1" long nap roller.
For smooth surfaces, apply at a spread rate of about 400 sq. ft. (37m²) per gallon using a nylon brush, short nap roller or a quality airless sprayer. For sprayer, use a .015-.017 size tip and follow manufacturer's recommendations for water-based coatings. If applying a second coat, spread rate is approximately 500 sq. ft. (46m²) per gallon on smooth surfaces; 300 sq. ft. (28m²) per gallon on rough surfaces.
Maintain a wet edge to avoid lap marks. Do not re-spread or re-work paint.
Wear appropriate respirator, eye and apparel protection when using a sprayer.
Dries to touch in approximately 2 to 3 hours at 75ºF and 50% relative humidity.
Recoat in four hours.
Additional dry time is needed in cooler temperatures and higher humidity.
Cures in about two weeks. Cured paint film may be cleaned with a mild, non-abrasive liquid detergent.
Clean tools and spills with warm, soapy water.
For dried spills, scrub and use hot water and a household detergent. Rinse with water.
Properly dispose of all soiled rags and protect unused product from freezing.
To recycle or properly dispose of paint in your community call 1-800-CLEANUP (U.S.A. only) or visit www.Earth911.org.
* Warning! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
WARNING! Sanding or scraping pressure treated lumber may be hazardous; wear appropriate protection.
WARNING! This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.
WARNING! IRRITANT! HARMFUL IF SWALLOWED.
CONTAINS: ETHYLENE GLYCOL. MAY CAUSE EYE, NOSE AND THROAT IRRITATION. AVOID CONTACT WITH SKIN AND EYES AND AVOID BREATHING OF VAPORS AND SPRAY MIST. WEAR EYE PROTECTION AND PROTECTIVE CLOTHING. USE ONLY WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air. If properly used, a respirator (NIOSH approved for organic vapor with P series particulate pre-filter) may offer additional protection; obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.
CAUTION: KEEP OUT OF REACH OF CHILDREN - DO NOT TAKE INTERNALLY.
LIMITED WARRANTY: Behr Process Corporation warrants your satisfaction with this product for 20 years on vertical surfaces from date of purchase, when applied to a properly prepared surface in accordance with the label directions. Color fading and chalking will occur naturally over time. If this product fails to perform as specified, Behr will, at its option and upon proof of purchase, either furnish an equivalent amount of new product or refund the purchase price. This warranty is made to the original residential product purchaser and is not transferable. Behr will not be responsible for (1) labor or the cost of labor for removal or application of any product or (2) any incidental or consequential damages, whether based upon breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Being a leader in our industry requires one resource above all others - great people. To successfully respond to the changing needs of our customers and strategies of our competitors, BEHR has identified, developed, and retained quality people who... more