Login:   Password:
Not Register?    Sign Up NOW!
Date: 17 October 2018
1-Part Epoxy Acrylic Concrete & Garage Floor Paint  
Search Country   Reset filter
1-Part Epoxy Acrylic Concrete & Garage Floor Paint

Sponsored Link:

1-Part Epoxy Acrylic Concrete & Garage Floor Paint

Sponsored Link:

Product Description

AUTION: PAINTED SURFACES MAY BECOME SLIPPERY WHEN WET. Adding BEHR® NO. 970 NON-SKID FLOOR FINISH ADDITIVE will help prevent slip. Follow all label instructions. Adding a non-skid additive will reduce the life span of the product therefore, retain any leftover paint for periodic maintenance re-coating.


(The following steps are recommended for best results)
Proper surface preparation is essential for adhesion of the paint.
Painted, Stained or Sealed Concrete:
Remove any loose or peeling paint and scuff sand the surface.
CLEAN: All surfaces must be clean, sound, dry, and free of any dirt, dust, oil, wax, or grease using BEHR NO. 990 CONCRETE CLEANER & DEGREASER. Rinse and allow to dry.
ETCH: Use BEHR NO. 991 CONCRETE ETCHER & RUST REMOVER on all areas where loose or peeling paint was removed. (Follow instructions from uncoated concrete section below). Allow to dry.
PRIME: Apply BEHR NO. 880 CONCRETE BONDING PRIMER to all uncoated concrete areas. Following all label instructions. Allow Concrete Bonding Primer to dry at least 8 hours before topcoating.
New And Uncoated Concrete or Masonry Surfaces:
Check for an unseen waterproofer on the surface by sprinkling a few drops of water on the surface to be top-coated. If water completely absorbs into the surface within a few minutes, the surface is ready for cleaning. If water beads and continues to stay on top of the surface, you will need to strip the entire surface with a chemical stripper. After stripping, re-test surface for repellency.
New concrete must cure for a minimum of 30 days.
CLEAN: All surfaces must be clean, sound, dry, and free of any dirt, dust, oil, wax, or grease. Use BEHR NO. 990 CONCRETE CLEANER & DEGREASER. Rinse and allow to dry.
Remove mildew stains with BEHR® NO. 62 MULTI-SURFACE CLEANER & MILDEW STAIN REMOVER. Refer to product labels for specific instructions.
ETCH: For proper penetration and adhesion of topcoats, use BEHR NO. 991 CONCRETE ETCHER & RUST REMOVER. Refer to product label for specific instructions.
Wear appropriate eye, skin and apparel protection when applying etching solution. Protect plants and other surfaces from splashing.
Tip: Use a plastic watering can to apply the etcher.
Working in small sections, apply solution into surface with a stiff bristle broom. On sloped surfaces, work from the lowest point to the highest.
Allow etching solution to remain on surface for 5 to 10 minutes. Keep area wet before and during etching. Scrub while rinsing thoroughly with clean water and allow to dry.
Tip: A pressure washer may be used for best results.
Test the surface by applying duct tape to the etched areas and pull back up. The tape must be clean and free of any concrete dust or dirt. If particles or a white residue are still present, it must be removed with additional scrubbing and rinsing with BEHR NO. 990 CONCRETE CLEANER & DEGREASER. Check the surface for water penetration by applying a few drops of water. Water should penetrate the surface.
br>PRIME: Apply BEHR NO. 880 CONCRETE BONDING PRIMER while following label instructions. Allow Concrete Bonding Primer to dry at least 8 hours before topcoating.
DO NOT THIN PRODUCT! Intermix all cans of same product to ensure color uniformity. Stir before applying.
Use product when air and surface temperature are between 50-90° F (10-32°C).
Apply a thin even coat using a 3/8 nap roller cover, pad applicator or a nylon/polyester brush at a spread rate of 400-500 sq. ft. (37-46m²) per gallon on smooth surfaces and 300-400 sq. ft. (28-37m²) per gallon on rough surfaces.
Allow first coat to dry 24 hours before deciding if a second coat is necessary. Apply a second coat (in a criss-cross direction) only if uniformity is needed.
DO NOT APPLY MORE THAN TWO COATS. An annual touch-up may be required for areas subject to tire traffic.
Dry Time
Dries to touch in two hours. Longer time required in cooler temperatures and higher humidity.
The floor may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to heavy foot traffic or repositioning furniture. Allow 7 days before subjecting painted surface to automotive tires.
If necessary, corrugated cardboard may be used underneath automobile tires after 72 hours.
Premature heavy traffic will cause paint failure requiring spot recoating.
Wait at least 30 days before rinsing or cleaning with a mild detergent.
Abrasive cleaners and pressure-washers should be used carefully to avoid premature paint failure.
Clean Up
Clean-up brushes, roller covers and tools immediately after use with soap and water.
Properly dispose of all soiled rags. Protect unused product from freezing.
To recycle or properly dispose of paint in your community call 1-800-CLEANUP (U.S.A. only) or visit www.Earth911.org.
* Warning! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

WARNING! This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm.

USE WITH ADEQUATE VENTILATION. To avoid breathing vapors and spray mist, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air and use a properly fitted respirator (NIOSH approved for organic vapor with P Series particulate prefilter). Obtain professional advice before using. A dust mask does not provide protection against vapors. Avoid contact with eyes and skin. Wash thoroughly after handling. Close container after each use. FIRST AID: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued difficulty is experienced, get medical assistance immediately. In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention; for skin, wash thoroughly with soap and water. If swallowed, get medical attention immediately.

LIMITED WARRANTY: Behr Process Corporation warrants that this product meets Behr's manufacturing specifications. If this product does not meet these specifications, Behr will, at its option and upon proof-of-purchase, either furnish an equivalent amount of new product to you or refund the purchase price of this product. Behr will not be responsible for (1) labor or the cost of labor for removal or application of any product; or (2) any incidental or consequential damages, whether based on breach of express or implied warranty, negligence, strict liability or any other legal theory. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

Company Details

Being a leader in our industry requires one resource above all others - great people. To successfully respond to the changing needs of our customers and strategies of our competitors, BEHR has identified, developed, and retained quality people who... more

More Products of this Company: BEHR PREMIUM PLUS WITH STYLE® Bellagio Faux™ No. 725, BEHR PREMIUM PLUS WITH STYLE® Crackle No. 755, BEHR PREMIUM PLUS WITH STYLE® Crystal Clear Water Based Polyurethane No. 780, BEHR PREMIUM PLUS WITH STYLE® Faux Glaze No. 748, BEHR PREMIUM PLUS WITH STYLE® Metallic, BEHR PREMIUM PLUS WITH STYLE® Pearlescent, BEHR PREMIUM PLUS WITH STYLE® SandWash Foundation No. 765, BEHR PREMIUM PLUS WITH STYLE® SandWash No. 760, BEHR PREMIUM PLUS WITH STYLE® Venetian Plaster No. 770, BEHR PREMIUM PLUS WITH STYLE® Venetian Plaster Topcoat No. 775, Masonry, Stucco & Brick Paint Flat, Masonry, Stucco & Brick Paint Satin, No. 61 BEHR Deck Wash, No. 62 Multi Surface Cleaner and Mildew Stain Remover, No. 875 Basement & Masonry Waterproofing Paint, No. 880 Concrete Bonding Primer, No. 980 Concrete & Masonry Waterproofer, No. 990 Concrete Cleaner & Degreaser, No. 991 Concrete Etcher & Rust Remover, PREMIUM PLUS Interior / Exterior Hi-Gloss Enamel, PREMIUM PLUS Interior Ceiling Paint No. 558, PREMIUM PLUS Interior Eggshell Enamel, PREMIUM PLUS Interior Enamel Undercoater Primer & Sealer No. 75, PREMIUM PLUS Interior Flat, PREMIUM PLUS Interior Kitchen & Bath Sateen Lustre Enamel, PREMIUM PLUS Interior Satin Enamel, PREMIUM PLUS Interior Semi-Gloss Enamel, PREMIUM PLUS P.V.A Drywall Primer & Sealer No. 73, PREMIUM PLUS® Interior Flat Enamel, PREMIUM PLUS® Porch & Floor Paint, Semi-Transparent Concrete Stain, Solid Color Concrete Stain, Wet-Look Sealer
Related Products: Conductors, High Glossy UV Varnish, Less Solvent OPP Lamination Glue, Screen-Printing UV Varnish, 1-amp buck regulator can be programmed to one of four output voltages, 1-amp buck regulator can be programmed to one of four output voltages, 1-amp buck regulator can be programmed to one of four output voltages, 1/3 & 3/4 HP Fixed Speed, Variable Length Turbines, 10-BASE T, 100% Tested!, 100-BASE T, 1000-BASE T, 101 Large Corner Roller, 111 Stratoflex medium pressure hose, 116DEXMRINH-GW Series AdaptaBeacon Explosionproof Rotating Lights, 116DEXMSINH-GW Series AdaptaBeacon Explosionproof Steady-On Lights, 116DEXMST-FJ Series AdaptaBeacon Explosionproof Strobes, 116DEXSTC-FJ AdaptaBeacon Explosionproof Strobe, 116EXMRIN Series AdaptaBeacon Explosionproof Rotating Lights, 116EXMST*-N5 Series AdaptaBeacon Explosionproof Strobes, 116EXST*-EK Series AdaptaBeacon Explosionproof Strobes, 120 mm Mortar Ammunition Family, 120 mm Mortar Weapon System, 147-10 Mounting Plate, 1500 Series Door Holder Extension Rods
Home | Members.Benefit | Privacy.Policy | Bookmark.This.Page | Contact.Us
Conveyor technology

© 2006 - 2018 Engineering Information. All Rights reserved.